Through the application of the self-cleaning system of the filter screen of the shaping machine, it can ensure the cleaning of the filter screen, avoid the blocking of the screen, reduce the hidden danger of the fire safety of the shaping machine, improve the output and ensure the quality stability; reduce the height of the drying room, cancel the opening of all the suction type filter screen ovens, and reduce the energy consumption to a greater extent; at the same time, because of the use of the automatic cleaning function, it can reduce the operation. The amount of work done as a worker. Therefore, the application of this technology has played a positive role in reducing fire hazards, improving product stability, reducing energy consumption and improving the degree of automation.
High consumption of conventional shaping function and low safety factor
Setting is the last process in the printing and dyeing process, which affects and determines the quality and performance of products to a great extent.
The setting process of textile printing and dyeing is completed in the drying room. The wet fabric will pass through the drying room continuously at a certain speed. The hot air provided by the heat source will enter the upper and lower air ducts respectively at a certain flow rate after being adjusted by the air volume distribution mechanism under the action of the high-power blower set at one side of the drying room. The upper and lower air ducts are uniformly distributed with hot air nozzles on the surface close to the fabric. The hot air blown by the blower forms a certain wind speed after passing through the hot air nozzle in the air duct, which acts on the whole width of the wet fabric in two directions, realizing the ironing of the fabric. After ironing, the hot and humid exhaust gas enters the exhaust heat exchanger through the exhaust machine, and is discharged after exchanging heat with the air at normal temperature.
Generally speaking, each setting machine is connected by eight or nine stages of drying rooms in series. The length of a single drying room is 3-4 meters, the width is 4-5 meters, and the volume is nearly 40 cubic meters. The whole setting machine has a large volume of equipment, and a large number of power sources and heat sources, making the energy consumption of the setting section account for more than 1 / 3 of the total energy consumption of the whole printing and dyeing production process, and the exhaust gas emission accounts for more than 1 / 2 of the total exhaust gas emission of printing and dyeing. Up. Taking the medium-sized printing and dyeing enterprises with 10 shaping machines as an example, the annual power consumption of the shaping section alone is 20 million degrees, while that of the enterprises of the same scale in the developed countries in Europe is only about 62% of that in China due to the use of advanced shaping equipment and control technology, with a huge difference in energy consumption.
The special working process of the shaping machine also increases the "danger" of its use to a great extent. From the data that the author has at present, the shaper is very prone to fire, and even some enterprise leaders think that the shaper is not on fire. For example, in 2012, 158 shaping machine fires occurred in Shaoxing County, seriously affecting the safety of life and property.
From the analysis, the shaping machine is prone to fire, mainly caused by three aspects. One is that the heat source of the shaping machine is heat conduction oil and electric heating. The leakage of heat conduction oil and the failure of electric heating temperature control device are easy to cause fire. The second is that the organic oil produced by heating the fabric in the oven of the setting machine and the flying flowers and fiber particles produced on the surface of the fabric mix to form the oil scale, which accumulates for a long time and is easy to cause fire in the oven. Third, some chemical fiber fabrics generate static electricity through mechanical operation friction, and the voltage can be as high as tens of thousands of volts, which is easy to cause electrostatic sparks, thus causing fire.
Therefore, how to prevent the fire of setting machine has become the focus of printing and dyeing enterprises. According to the summary of production experience, the heat-transfer oil pipeline and temperature control device in the oven of the shaping machine should be checked regularly, and a qualified organization should be hired to detect the pipeline. If there is any oil leakage, it should be handled in time; the oil pollution and flying flowers in the machine and the smoke exhaust pipe should be removed in time to eliminate the hidden danger of fire, which is particularly important. In addition, it is also necessary to carry out technical transformation of the shaping machine in time, add steam pipe on the exhaust pipe, open the steam to put out the fire in case of fire; install wire mesh shield on the radiator to prevent flying flowers from falling on the radiator and causing combustion.
Four measures to reduce the energy consumption of shaping machine
At present, the main energy-saving ways of the shaping machine include direct gas combustion heating, heat transfer oil heating to hot steam heating, using new compact energy-saving shaping machine, waste gas waste heat recovery, etc.
Direct gas combustion heating is to install a direct combustion heating system in the oven of the shaping machine, so that the air is directly heated by the burner burning natural gas, and the hot gas circulation in the oven can reach the required temperature, which can reduce energy consumption. For example, after Changzhou xurong knitting printing and dyeing Co., Ltd. changed heat supply from heat transfer oil to direct combustion type, the average natural gas consumption of the shaping machine can be saved by 18% on the basis of statistical analysis of unit consumption data within one year of operation compared with that before the transformation.
Heat transfer oil heating is changed to steam heating. The way of heating the heat-transfer oil of the shaping machine needs each enterprise to set the heat-transfer oil boiler, but because the equipment is relatively simple, it is welcomed by the enterprise. The disadvantages of this method are the low thermal efficiency of coal-fired heat transfer oil boiler, the difficulty of dedusting and desulfuration, the poor performance of enterprises and the great environmental pollution. The steam in the hot steam heating mode can be directly supplied by the thermal power plant in the way of central heating, with high thermal efficiency. It is easy to control the pollution and it is a better way to save energy and reduce emissions. However, due to the need to lay high-pressure steam pipes, the heat exchanger in the shaping machine also needs to be replaced, so the general enterprise is not very active in this technical transformation.
At present, a new type of compact energy-saving shaping machine has appeared in the international market. Its hot air circulation is changed from the traditional installation of fans on the left and right sides to the installation of fans at the top and bottom at the same time. In the form of up and down fans, the return air distance is short, the heat source is fully utilized, and the waste of heat energy is less. The volume of the new shaping machine is only 1 / 3 of that of the traditional one. The reduction of the volume reduces the heat dissipation area of the body and makes full use of the energy inside the oven. If the shaping machine does not contact with the ground directly, it can also save a lot of energy.
The waste gas from the setting machine accounts for 61% of the total heat energy. The temperature of the waste gas from the processing of chemical fiber products is 160 ℃ ~ 170 ℃, and the temperature of the waste gas from the processing of cotton products is 100 ℃ ~ 110 ℃. The waste heat recovery heat exchanger is welded with aluminum tube or copper tube. The high-temperature waste gas passes through the channel outside the heat exchange tube, and the fresh air passes through the channel inside the heat exchange tube. The two channels are completely isolated. Fresh air is absorbed into heat exchanger by fan for heat exchange, and it can be heated to about 30 ℃ ~ 40 ℃ different from high temperature waste gas. Centralized waste heat recovery, the temperature of the heated fresh air is relatively high, but the air flow is relatively large, direct recycling will affect the internal air flow of the setter, using the barrel dryer, can make full use of the heat energy of the waste gas. In addition, the waste heat recovery can cool the waste gas discharged by the shaping machine to 60 ℃ ~ 70 ℃, which is convenient for the purification of the waste gas.






