Dec 19, 2019 Leave a message

Points of attention for carding machine to control neps impurities

Many recent articles on carding machines, for technical analysis, must be qualitative and quantitative analysis. Although this article is short, it is excellent in qualitative analysis. In quantitative analysis, the numbers listed also have certain reference significance.


1, enhanced carding


Reinforced carding can promote fiber straightening, break down into single fibers, and promote separation of fibers from impurities, while also loosening the neps. Therefore, the "quasi" of the main carding interval and the sharpness of the carding element are extremely important.


2, reasonable division of labor


It is most beneficial to grasp what impurities fall in what processes and parts, that is, to reasonably divide the work to eliminate impurities, and to properly remove the various parts of the card itself. Generally, the impurities that are relatively large and easy to be separated and eliminated should implement the principle of early falling and less broken, and fall early in the cleaning process. It is more advantageous to eliminate fiber impurities with large adhesion, especially those with long fibers, on the card. Therefore, when the maturity of the raw cotton is poor and there are many harmful defects in the fiber, the card removal machine should be appropriately added to remove impurities and waste. The licker-in part of the card should eliminate broken seeds, stiff petals and fluff, as well as fine impurities with shorter fibers. The cover is suitable for eliminating fine impurities, neps, and lint.


For general domestic cotton, the total noil rate of carded cotton is greater than that of Kaiqing cotton. The impurity removal efficiency of cotton cleaning (contamination of raw cotton) should be controlled at 50% -65%, and the efficiency of cleaning removal of cotton lint rollers (contamination of cotton roll) should be controlled at 50% -60%. The efficiency is controlled in the range of 3% -10%, and the impurity ratio of the sliver should generally be controlled below 0.15%.


The focus of controlling impurities on the carding machine is in the licker-in part, and the production parameters are adjusted by adjusting the process parameters of the bottom of the small leak and the dust removal knife, such as the inlet gap of the bottom of the small leak and the fourth point separation, and the height of the dust removal knife. When the maturity of the raw cotton is poor and the cotton roll contains more impurities, which results in an increase in the sliver impurity, a small gap at the bottom of the inlet should be accepted, and the length of the impurity removal zone should be increased to adjust. The suction tube on the cover of the licker-in roller should not be blocked, otherwise the abdomen of the back car will become abnormal and the whiteness will increase. The length of the small bottom chord is too long, and the specifications of the toothing of the licker-in roller are not suitable. The card clothing specifications of the cylinder and the cover, the distance between the front upper cover and the cylinder, the height of the mouth position of the front upper cover, and the speed of the cover also all affect the number of slivers and neps.


3. Reduce rubbing


的 The neps produced on the card are mainly formed by returning flowers, winding flowers, and fiber rubbing. For example, when the distance between the cylinder and the doffer, the cylinder and the cover are too large and the needle teeth are blunt, the fiber is rubbed excessively, and the return of the licker-in roll and the coil of the cylinder will increase the neps. The process of opening and clearing cotton is serious, the moisture regain of cotton coils is too high, the mixed ratio of recycled flowers and reused cotton is too large, or uneven feeding, etc., all will increase the sliver neps.


Reasonable cotton distribution and strengthening temperature and humidity management have a considerable effect on reducing neps and impurities. Several factors, such as maturity, harmful defects, and impurities, that have a greater impact on yarn formation during cotton blending should be controlled to control the differences in the indicators. When the moisture regain of raw cotton and cotton rolls is low, the impurities are easy to fall, and the end of cotton can be reduced. Therefore, the moisture regain of cotton rolls should be controlled not to exceed 8% -8.5%, and the raw cotton not to exceed 10% -11%. Control the lower relative humidity in the carding workshop. For example, the relative humidity should be controlled at 55% -60% to make it wet, increase the rigidity and elasticity of the fiber, and reduce the friction and stuffing between the fiber and the clothing. However, if the relative temperature is too low, static electricity is easily generated, and the cotton web is easily broken, adhered or broken. This phenomenon is even more pronounced when spinning chemical fibers. Relative humidity is too low, at the same time will reduce the moisture regain of the sliver, which is not good for the subsequent drafting process.


The use of high-quality alloy copper card clothing, strengthening the carding effect, and increasing the suction point and air suction volume on each card can reduce sliver knotting to a large extent.


Send Inquiry

whatsapp

Phone

E-mail

Inquiry